Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in South Fulton?
Panel replacement in South Fulton typically costs $250-$500 for a single damaged section, including the new panel and installation. That figure covers the most common job: one or two dented or cracked sections on a standard residential door. Bigger damage, unusual panel sizes, or a discontinued door style can push the estimate higher, and the written estimate you get on site is the number that sets the final price.
A dented panel is easy to ignore until you notice the door no longer seals at the bottom, or you can see daylight through it. Once that happens, the fix is usually smaller than homeowners expect. We run through the numbers below so you can decide whether a panel swap makes sense or whether a different repair fits better.
Our technicians have up to 14 years of experience, and we work on panels for every major door brand, including Clopay, Amarr, Wayne Dalton, and Raynor. If your door is one of those, the panel almost always comes from stock or a short order rather than a weeks-long wait.
Key Takeaways
- Typical panel replacement in South Fulton runs $250-$500 for a standard single section.
- Two or more panels can move the job into the $450-$700 range depending on size and brand.
- Matching the panel to your existing door is the biggest cost factor, not the labor.
- Storm and impact damage drives most panel jobs in the South Fulton area.
- We service Clopay, Amarr, Wayne Dalton, Raynor, and other major door brands, so a matched panel is usually within reach.
If you want a straight answer for your specific door, call (855) 765-9962. Estimates are free and we don’t guess at a price over the phone when a photo tells us more.
Panel Replacement Cost Breakdown (2026)
Here’s how the typical estimated price ranges break down for South Fulton. These are for residential doors and cover both parts and labor. The written estimate you receive on site is the final word on price.
| Job | Typical Estimated Range |
|---|---|
| Single standard panel (one section) | $250-$500 |
| Two adjacent panels | $450-$700 |
| Bottom panel (most common, includes weather seal) | $250-$500 |
| Window panel or panel with inserts | $300-$550 |
| Panel plus realignment of affected track | $350-$650 |
| Panel plus roller replacement (when worn rollers caused the damage) | $350-$600 |
| Clopay, Amarr, Wayne Dalton, Raynor matched panel | $250-$500 |
The single biggest driver is whether your door’s panel style is still being made. A current Clopay or Amarr panel slides right into place. A discontinued style means we either track down the last panels in circulation or recommend a face-lift that looks close to the original. Labor on a standard panel swap is a small part of the bill; the panel itself is most of it. Bottom sections and window panels run at the top of the range because they carry seals, inserts, and glass.
If the panel damage came with bent track or a snapped spring, the fix grows past a simple swap. A track realignment typically runs $120-$240 and spring repair runs $180-$340 for one spring. A matched pair of springs, which is what we usually recommend replacing together, costs about twice that.
What Affects Panel Replacement Pricing in South Fulton
South Fulton is a large, spread-out part of Fulton County covering communities like Sandtown, Campbellton, Red Oak, and the area around Old National Highway. Most of the housing stock is single-family, and a lot of it was built in the 1990s and 2000s, which means the panel styles and door brands from that era are what we see most. Here’s what actually moves the price:
- Panel availability. If your door style is still in production, a Clopay, Amarr, Wayne Dalton, or Raynor panel is a straightforward order. If it’s been discontinued, we have to hunt for a match, and that search is the single biggest swing in price.
- Panel size and design. Standard single-car panels are the cheapest. Double-car and custom-width panels cost more because the material is larger. Window panels, decorative inserts, and carriage-style panels add to the bill.
- Number of panels. One section is the common job. Two or three panels together usually get a small break on labor, but the material cost stacks up.
- Damage underneath. A dented panel is one thing. If the impact that dented it also bent a hinge, cracked a roller, or knocked the track out of line, we need to fix those too. Bent track often shows up with a panel job because a car hit the door hard enough to do both.
- Door type. Sectional doors are the norm and easy to quote. A one-piece tilt door or a custom door can be different, and we’ll always tell you before we start.
- Weather sealing. Replacing the bottom panel is a natural time to swap the bottom weather seal. It’s a small add to the total and saves you a second visit later.
One thing that comes up often in this part of Georgia is storm damage. Wind-driven debris and fallen limbs are the usual cause of a dented or cracked panel, and the damage is rarely confined to one spot. When a limb hits a door, we usually find a dented panel plus a bent hinge, so the estimate covers the whole repair rather than just the section.
How to Save on Panel Replacement
Panel replacement isn’t the place to chase the lowest number, but there are real ways to keep the bill down:
- Catch it early. A small dent that gets repaired before it spreads to the weather seal or the track is the cheapest version of this job. Waiting usually means fixing more than the panel.
- Replace only what’s damaged. You don’t need a whole new door because one section is dented. We’ll tell you honestly when a single panel is enough and when it isn’t.
- Pair it with routine fixes. If your rollers are worn or your bottom seal is shot, handle them during the same visit and skip a second call-out. We don’t pad the visit with work you don’t need.
- Ask about the panel type. A standard panel in a current style is the most affordable option. If you’ve been thinking about a different look, a face-lift that uses a current panel can be less than tracking down a discontinued one.
- Get a free estimate. Send us a photo of the damage and we’ll tell you whether it’s a panel job or something simpler. Call (855) 765-9962 and there’s no charge to look.
One point worth knowing: if the damage is from a fall or a car hit, your homeowner’s policy may cover it. That’s between you and your insurer, but the written estimate we provide is what you’d hand them. We don’t quote a price we can’t stand behind.
Why Homeowners in South Fulton Call Us for Panel Work
Panel work is a small job, and it’s easy for a homeowner to get the runaround: a company that doesn’t carry your brand, or one that wants to sell you a new door when a single panel would do. We’re set up to avoid both. We’re certified to service eight of the most common garage door and opener brands in the industry, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. When your door is one of those, we know the panel sizes and where to source a match.
We also handle the whole system, not just the panel. If your opener is Genie, LiftMaster, Chamberlain, or Craftsman and it’s acting up at the same time, we can diagnose it on the same visit. If the door was damaged by a snapped spring, we handle torsion and extension springs as part of the same call. And when a door fails and you need it working again soon, emergency service is a core part of what we do, not a next-week appointment. For more on the full repair scope, see panel replacement or start at South Fulton Garage Door Repair.
Here’s the safety piece we never skip: the springs and cables under tension are what lift the door, and a panel swap often requires relieving that tension to free the section. That’s the most dangerous part of any garage door job, and it’s exactly why we handle it rather than tell you to. A door that’s been hit or has a failed spring can drop the minute its balance is disturbed. Call us and we’ll take that risk off your hands.
FAQs – Panel Replacement Cost
How much does panel replacement cost in South Fulton?
Panel replacement in South Fulton typically costs $250-$500 for a single standard panel, installed. A bottom panel with a new weather seal runs at the top of that range. Call (855) 765-9962 for a free estimate on your door, and we’ll give you the exact number in writing.
Is it cheaper to replace a panel or the whole door?
For a single damaged panel, replacing the panel at $250-$500 is far cheaper than a new door installation at $700-$2200. The panel swap is almost always the right call unless the damage covers multiple sections or the door’s frame and hardware are failed. Call (855) 765-9962 and we’ll tell you which one your door actually needs.
Can you match my existing door color and style?
Usually, yes. If your door is a Clopay, Amarr, Wayne Dalton, or Raynor in a current style, a matched panel is a standard order and the color matches. If the style is discontinued, we’ll tell you upfront and walk through the alternatives. Call (855) 765-9962 with your door brand and style; estimates are free.
Can you come today for panel replacement?
Same-day and emergency service is a core offering, so call and we’ll tell you what’s available. Same-day service on a panel job depends on whether the panel is in stock and whether the door is safe to operate in the meantime. Call (855) 765-9962 for an honest answer on timing.
Does a panel replacement include fixing bent track or a broken spring?
Not always. A straight panel swap covers the panel and its installation. Bent track is a separate realignment at $120-$240, and spring repair is $180-$340 for one spring, with a matched pair costing about twice that. We’ll tell you before we start if the door needs more than the panel. Call (855) 765-9962 for a free on-site estimate.
If your door needs a bottom section, a window panel, or a match for a specific brand, one call sorts it out. We work on your brand, whether that’s Clopay, Amarr, Wayne Dalton, Raynor, or another major door maker, and we don’t stop at the panel if the track or springs need attention. Call (855) 765-9962 for a free estimate. We’ll look at the damage, give you a written range, and tell you honestly whether a panel swap is enough.
Pricing reflects the South Fulton market as of 2026. South Fulton Garage Door Repair offers free estimates – call (855) 765-9962.
Written by the team at South Fulton Garage Door Repair.
What Our Customers Say
"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Heather Anderson"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."
- Brian Hayes"Good repair, reasonable money. The door still has a slight shudder about a foot from the top that he said is the track being slightly out of true on an old frame and would cost real money to fix properly. Fair enough, but I'd hoped it would be perfect."
- Paul Norris